详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

Using TensorFlow-based Neural Network to estimate GNSS single frequency ionospheric delay (IONONet)

In the last 20?years, and in particular in the last decade, the availability of propagation data for GNSS has increased substantially. In this sense, the ionosphere has been sounded with a large number of receivers that provide an enormous amount of ionospheric data. Moreover, the maturity of the models has also been increased in the same period of time. As an example, IGS has ionospheric maps from GNSS data back to 1998, which would allow for the correlation of these data with other quantities relevant for the user and space weather (such as Solar Flux and Kp). These large datasets would account for almost half a billion points to be analyzed. With the advent and explosion of Big Data algorithms to analyze large databases and find correlations with different kinds of data, and the availability of open source code libraries (for example, the TensorFlow libraries from Google that are used in this paper), the possibility of merging these two worlds has been widely opened. In this paper, a proof of concept for a single frequency correction algorithm based in GNSS GIM vTEC and Fully Connected Neural Networks is provided. Different Neural Network architectures have been tested, including shallow (one hidden layer) and deep (up to five hidden layers) Neural Network models. The error in training data of such models ranges from 50% to 1% depending on the architecture used. Moreover, it is shown that by adjusting a Neural Network with data from 2005 to 2009 but tested with data from 2016 to 2017, Neural Network models could be suitable for the forecast of vTEC for single frequency users. The results indicate that this kind of model can be used in combination with the Galileo Signal-in-Space (SiS) NeQuick G parameters. This combination provides a broadcast model with equivalent performances to NeQuick G and better than GPS ICA for the years 2016 and 2017, showing a 3D position Root Mean Squared (RMS) error of approximately 2?m.     

空间激光通信系统中的信道纠错编码技术

由于空间激光通信系统的信道状态和链路捕获跟踪的不确定性,多种形式的信道纠错编码技术正被广泛发展研究。结合空间激光通信链路中误码性能的主要影响因素,分别选择合适的编码方案进行分析。通过仿真实验可知,对于在大气结构参数为1.5×10~(-14) m~(-2/3)、风速为20 m/s的空地激光链路的环境下,在系统数据速率为2 Gbit/s、要求误码率为10~(-6)时,LDPC码结合交织码相对未编码系统有3 dB的等效编码增益,LT码相对未编码系统有3.8 dB的等效编码增益。提供了一种能快速生成、扩展和校验的编码和交织实现方法,以抵抗大气湍流的快速变化对系统性能产生的影响。     

某机载探测系统自主回收技术的实现

针对某机载探测系统探头回收自动化程度低的问题，提出了在无需操作员干预情况下实现探头自主回收的技术方法。采用了先进的控制算法，将缆位角与探头、缆长进行结合并引入了绞车控制系统，使绞车对探头的回收速度及缆长可进行实时调整，并给出了3种不同缆位角摆动条件下缆长与探头回收速度的控制曲线关系。研发了自主回收装置，设计了能够实现自主回收功能的探头回收机构。实验验证表明：在无需人为干预的条件下，在缆位控制系统及自主回收机构的配合下，系统实现了对探头快速、安全的回收。     

平台式重力仪航空重力测量数据后处理技术研究

针对航空重力测量对数据后处理的要求,结合平台式重力仪系统的组成与工作原理,在重力异常信号的频域特征基础上,设计出一套有严格频域规范的航空重力数据后处理流程,并对某海域实测数据进行了处理。结果表明,重力异常值内符合精度为12条东西测线达到0.43mGal/140s和0.84mGal/100s,4条南北测线达到0.39mGal/140s和0.79mGal/100s;以同测线GT-2A单次测量结果为标准值统计标准差,12条东西测线为0.72mGal/140s和0.98mGal/100s,4条南北测线为1.41mGal/140s和1.53mGal/100s。结果表明,设计的航空重力测量数据后处理方法可以实现重力异常信号的高精度提取。     

绳索断裂对二维二次太阳翼展开过程影响分析

为识别二维二次太阳翼关键环节和预示其在轨展开故障模式，开展不同位置绳索断裂失效对太阳翼展开的影响程度分析。采用考虑绳索断裂的绳索联动轮力学模型，建立了适应于不同联动轮半径的联动轮受力模型，提出角度触发约束消除方法，解决了太阳翼第2次展开过程连续仿真问题，建立了太阳翼第2次展开动力学方程，分析了不同位置绳索断裂失效对太阳翼各板展开角度、展开构型和其他绳索张力的影响。分析表明，越靠近星体的绳索联动机构失效对太阳翼展开过程的影响越大，其中连接架上绳索联动机构失效可直接导致二维二次太阳翼在轨展开失败。     

超静超稳卫星碰振动力学建模

针对分离式卫星载荷模块(PM)受到扰动时可能与服务模块(SM)发生碰撞的问题，综合音圈电机反电动势(back-EMF)和柔性线缆动力学的效应，基于牛顿欧拉法建立了分离式卫星(DFP)载荷模块动力学模型。基于Hertz接触理论，推导了分离式卫星碰撞过程中连续接触力模型，并分析了碰撞过程中产生的接触力对载荷模块指向精度和指向稳定度的影响。数值仿真结果表明，碰撞使得载荷模块指向精度和指向稳定度下降5个数量级，碰撞后载荷模块可再次恢复到超静超稳工作状态，恢复时间超过1400 s。本文建立的碰撞模型对研究分离式卫星碰撞规避和碰撞控制具有重要意义。     

A new modeling scheme for powered parafoil unmanned aerial vehicle platforms: Theory and experiments

A novel framework is established for accurate modeling of Powered Parafoil Unmanned Aerial Vehicle (PPUAV). The model is developed in the following three steps: obtaining a linear dynamic model, simplifying the model structure, and estimating the model mismatch due to model variance and external disturbance factors. First, a six degree-of-freedom linear model, or the structured model, is obtained through dynamic establishment and linearization. Second, the data correlation analysis is adopted to determine the criterion for proper model complexity and to simplify the structured model. Next, an active model is established, combining the simplified model with the model mismatch estimator. An adapted Kalman filter is utilized for the real-time estimation of states and model mismatch. We finally derive a linear system model while taking into account of model variance and external disturbance. Actual flight tests verify the effectiveness of our active model in different flight scenarios.     

全模颤振风洞试验三索悬挂系统多体动力学分析

全模颤振风洞试验需要通过软支撑系统模拟飞行器的自由飞行状态并调整模型姿态达到配平状态。参考NASA双索悬挂方案，提出了一种两电机驱动的三索悬挂系统，利用后方两索的同向/反向联动实现模型俯仰和滚转姿态的调整，利用弹簧刚度以及钢绳张力设计实现支撑频率要求。基于柔性多体动力学方法，建立了包括飞行器刚体模型、柔性索、滑轮、弹簧、气动力模型、伺服电机控制在内的复杂系统动力学模型，其中，利用任意拉格朗日-欧拉（ALE）变长度索单元描述钢绳，利用不约束物质坐标的索结点约束描述钢绳与滑轮相互作用，利用索结点物质输运速度约束描述伺服电机绞盘，利用飞行力学的气动力模型描述吹风下的气动力。基于该模型，通过小扰动响应辨识研究了弹簧刚度、钢绳张力、连接点位置等因素对支撑频率的影响规律，并分析了系统姿态调整能力，俯仰调整范围达到-12.5°~12.5°，滚转调整范围达到-45°~45°。采用滑轮处电位计测量的钢绳相对位移作为反馈信号，基于设计的控制律利用多体动力学求解器与Simulink对风洞吹风下的姿态调整过程进行仿真，模型达到配平状态，获得了吹风下的索拉力和伺服电机功率，为系统设计提供基础。